13 Jun Unit 3, Lab 2 – Place a 1-2 inch section of banana into a ziplock bag
Question
Unit 3, Lab 2
DNA Extraction from a Banana
Introduction:
As you are learning in Unit 3, DNA is the blueprint for life and resides in the cells of all living
things. In this experiment, you will extract DNA from a banana using a few basic ingredients,
many of which you may already have around the house.
In order to extract the DNA from cells, the cell and nuclear membranes must first be broken open
to allow the release of DNA. In a laboratory setting, this is done by mixing cells with a specific
type of detergent, which breaks apart (or lyses) the cell and nuclear membranes. In this case, we
will use kitchen dish detergent, which is a close cousin to the detergent used in labs. In order to
then isolate the DNA away from cellular debris, salt and alcohol are used. DNA is polar, and
therefore readily dissolvable in water. Salt and alcohol, however, reduce the polarity of the
DNA, causing it to separate (or precipitate) away from the water and become visible to the naked
eye as long, milky-looking strands. We will use table salt and 70% isopropyl alcohol (also
known as rubbing alcohol) for this step.
Materials:
Banana
Ziplock bag
Measuring spoons and cups
Ice-Cold Alcohol (70% Isopropyl Alcohol, or rubbing alcohol, stored in freezer for at least an
hour before the experiment)
Water
Table Salt
Liquid Dishwashing Detergent
Coffee filter (paper towel can be substituted)
Toothpick, wooden skewer or wooden coffee stirrer (optional)
Instructions:
1) Place a 1-2 inch section of banana into a ziplock bag. Using your fingers, knead and
squeeze the banana until it is a mushy consistency and no solid form remains.
2) Fill a measuring cup with ½ c lukewarm or room temperature water and add 1 tsp salt.
Stir to dissolve most or all of the salt.
3) Add the salt water mixture to the banana, seal the bag, and shake gently to mix for 45
seconds to mix.
4) Add 1 tsp liquid dish soap and again shake the bag gently for 45 seconds. Shake or
agitate gently to prevent too much dish soap foam from accumulating.
5) Set a coffee filter (or paper towel) over the top of a clear, narrow glass container, (a
drinking glass will do), pushing the center of the coffee filter down into the container
slightly, making a well, and overlapping the edges over the sides. If necessary, use a
rubber band to hold the filter in place.
6) Pour the banana mixture through the filter until most liquid containing the released DNA
has passed through, trapping the banana in the filter. You may have to pour the liquid
several times, waiting for it to drip through each time before adding more. You may also
discard the coffee filter and get a new one as the original one fills with banana making it
more difficult for the liquid to flow through.
7) Tilt your glass container at an angle and very slowly pour the ice cold isopropyl alcohol
down the inside of the container so that it slowly forms a layer on top of the DNA
mixture. Continue to pour until the layer of alcohol is approximately 1-2 inches thick.
8) Observe the interface where the food mixture and alcohol meet for approximately 5-10
minutes. The DNA will begin to accumulate in the alcohol layer as a milky-white,
stringy substance. You can gently swirl a toothpick or wooden skewer to observe the
clumps of DNA, doing your best to not disturb the interface. Allowing the experiment to
sit for longer (up to an hour) will allow for more DNA accumulation.
9) Take a picture of your results and upload it with your written assignment (below).
To Submit For a Grade:
Please complete the following short answer questions and submit them for your grade, along
with a picture of your completed experiment.
Please describe the purpose for each of the following reagents (ingredients) in your experiment.
In other words, why are these necessary in the DNA extraction process? Please use complete
and descriptive sentences when formulating your answers.
Banana:
Salt:
Dish Detergent:
Isopropyl Alcohol:
Our website has a team of professional writers who can help you write any of your homework. They will write your papers from scratch. We also have a team of editors just to make sure all papers are of HIGH QUALITY & PLAGIARISM FREE. To make an Order you only need to click Ask A Question and we will direct you to our Order Page at WriteDemy. Then fill Our Order Form with all your assignment instructions. Select your deadline and pay for your paper. You will get it few hours before your set deadline.
Fill in all the assignment paper details that are required in the order form with the standard information being the page count, deadline, academic level and type of paper. It is advisable to have this information at hand so that you can quickly fill in the necessary information needed in the form for the essay writer to be immediately assigned to your writing project. Make payment for the custom essay order to enable us to assign a suitable writer to your order. Payments are made through Paypal on a secured billing page. Finally, sit back and relax.
About Writedemy
We are a professional paper writing website. If you have searched a question and bumped into our website just know you are in the right place to get help in your coursework. We offer HIGH QUALITY & PLAGIARISM FREE Papers.
How It Works
To make an Order you only need to click on “Order Now” and we will direct you to our Order Page. Fill Our Order Form with all your assignment instructions. Select your deadline and pay for your paper. You will get it few hours before your set deadline.
Are there Discounts?
All new clients are eligible for 20% off in their first Order. Our payment method is safe and secure.